At Marco Rubber & Plastics, we provide a wide variety of compounds approved to nearly every military, aerospace, ASTM, SAE, automotive, petroleum industry and commercial specification. Many products are in stock and available to buy online. We stock many popular sizes of Mil-Specs Parts from QPL Manufacturers. Packaging per Mil-P-4861 is available upon request.
Of these specifications, the most widely used are AMS, AS, AN, M, MS, MIL, and NAS specifications. This reference table lists some of the specs available.
Compound # | Datasheet | Material Specification | Sizing Specification | QPL | Base Material | High Temp °F (°C) | Low Temp °F (°C) | Features | Superseded Size Spec | Superseded Material Spec |
---|---|---|---|---|---|---|---|---|---|---|
M1000 | AMS-P-25732 | MS28775 | QPL | NBR | 275 (135) | -65 (-54) | MIL-H-5606 petroleum base hydraulic fluid for military aircraft (inactive for new designs. see AMS-P-83461) | MS28784, MS28785 | MIL-P-25732, AN6227, AN6230 | |
M1001 | AMS-P-83461 | M83461/1, M83461/2 | QPL | NBR | 275 (135) | -65 (-54) | MIL-H-5606 Better dynamic performance and longer service life at 257°F than AMS-P-25732 (MS28775). M83461/1, M83461/2 Boss Tube Sizes | MIL-P-83461 | ||
M1002 | AMS-P-5315 | MS29513 , MS29512 | QPL | NBR | 158 (70) | -65 (-54) | MS29513 , MS29512 Boss Tube Sizes, Aircraft fuels | MIL-P-5315 | ||
M1004 | AMS-P-5510 | MS28778 | NBR | MIL-P-5510, AN6231, AN6290 | ||||||
M1005 | AMS 7271 | AS3578 | QPL | NBR | 257 (125) | -58 (-50) | Tube fitting sizes only. Not recommended for high pressure dynamic applications, Aircraft fuels | MS9020, MS9021 | ||
M1007 | AMS7270 | AS3569 | QPL | NBR | 302 (150) | -40 (-40) | For use in aircraft fuels, both piston (gasoline) and jet (jet fuels) engines. | AN123951, AN124050 | ||
M1008 | AMS-R-7362 | MS29561 | NBR | 180 (82) | -60 (-51) | MIL-R-7362, NAS61 | ||||
M1009 | AS3570 | AMS 7274 | NBR |
The information on this page is to the best of our knowledge accurate and reliable. However, Marco Rubber makes no warranty, expressed or implied, that parts manufactured from this material will perform satisfactorily in the customer's application. It's the customer's responsibility to evaluate parts prior to use.
The temperature ranges presented on this page are approximations for dry air service only and should not be used to determine design specifications or end-use temperature limits. Actual temperature range of a compound in an end-use application is highly dependent on part type, hardware configuration, applied forces, chemical media, pressure and thermal cycling effects, and other factors. The most practical way of determining an end-use temperature range is testing in the actual application conditions. Consult a Marco Engineer for more details.
Material Specification | Sizing Specification | Features |
---|---|---|
AS3551 | ||
AMS 3216 | ||
AS43013, AS43003 | AS43013, AS43003 Boss Tube Sizes | |
AMS 3383 | Aircraft fuels and lubricants | |
AMS 3325 | Blue color as required by MIL spec, Aircraft fuels and lubricants | |
AS9386, AS9385 | AS9386, AS9385 Boss Tube Sizes, Dry heat and petroleum based lube oils | |
ASM 3302 | MS27290 | |
AMS 3303 | MS26577 | |
AMS 3195 | Medium Closed Cell Silicone Rubber Sponge | |
AMS 3196 | Firm Closed Cell Silicone Rubber Sponge | |
AMS 3197 | Soft Chloroprene-Rubber Sponge | |
AMS 3198 | Medium Chloroprene Type Synthetic Rubber Sponge | |
AMS 3199 | Firm Chloroprene Type Synthetic Rubber Sponge | |
AMS 3200 (B) | Petroleum-Base Hydraulic Fluid Resistant Nitrile Rubber 55-65 Durometer | |
AMS 3201 (B) | Dry Heat Resistant Synthetic Rubber 35-45 Durometer | |
AMS 3202 (B) | Dry Heat Resistant Synthetic Rubber 55-65 Durometer | |
AMS 3204 (B) | Low Temperature Resistant Synthetic Rubber 25-35 Durometer | |
AMS 3205 (B) | Low Temperature Resistant Synthetic Rubber 45-55 Durometer | |
AMS 3206 | Extreme Pressure Lubricant Resistant Synthetic Rubber 65-75 Durometer | |
AMS 3207 (B) | Weather Resistant Chloroprene Rubber 25-35 Durometer | |
AMS 3208 (B) | Weather Resistant Chloroprene Type Synthetic Rubber 45-55 Durometer | |
AMS 3209 (B) | Weather Resistant Chloroprene Type Synthetic Rubber 65-75 Durometer | |
AS 3209 (B) | Preformed Packing. 70-80 durometer, high temperature, fluid resistant, low compression FKM per AMS7276. | |
AMS 3210 (B) | Electrical Resistant Chloroprene Rubber 65-75 Durometer | |
AMS 3212 (B) | Aromatic Fuel Resistant Acrylonitrile Butadiene (NBR) Rubber 55-65 Durometer | |
AMS 3213 (B) | Aromatic Fuel Resistant Acrylonitrile Butadiene (NBR) Rubber 75-85 Durometer | |
AMS 3214 (B) | Aromatic Fuel Resistant Acrylonitrile Butadiene (NBR) Rubber 35-45 Durometer | |
AMS 3215 (B) | Aromatic Fuel Resistant Acrylonitrile Butadiene (NBR) Rubber 65-75 Durometer | |
AMS 3216 (B) | Fluorocarbon Rubber – Fuel and Oil Resistant | |
AMS 3220 (B) | Synthetic Rubber 55-65 Durometer | |
AMS 3222 (B) | High Swell Hot Oil Resistant Synthetic Rubber 45-55 Durometer | |
AMS 3226 (B) | Low Swell Hot Oil and Coolant Resistant Synthetic Rubber 45-55 Durometer | |
AMS 3227 (B) | Low Swell Hot Oil and Coolant Resistant Synthetic Rubber 55-65 Durometer | |
AMS 3228 (B) | Low Swell Hot Oil and Coolant Resistant Synthetic Rubber 65-75 Durometer | |
AMS 3229 (B) | Low Swell Hot Oil Resistant Synthetic Rubber 75-85 Durometer | |
AMS 3230 | Oil Resistant Gasket | |
AMS 3231 | Synthetic Rubber Binder Oil Resistant Gasket | |
AMS 3237 (B) | Phosphate Ester Resistant Butyl Rubber 35-45 Durometer | |
AMS 3238 (B) | Phosphate Ester Resistant Butyl Type Synthetic Rubber 65-75 Durometer | |
AMS 3239 (B) | Phosphate Ester Resistant Butyl Type Synthetic Rubber 85-95 Durometer | |
AMS 3240 (B) | Weather Resistant Chloroprene Rubber 35-45 Durometer | |
AMS 3241 (B) | Weather Resistant Chloroprene Type Synthetic Rubber 55-65 Durometer | |
AMS 3242 (B) | Weather Resistant Chloroprene Type Synthetic Rubber 75-85 Durometer | |
AMS 3243 (B) | Flame Resistant Chloroprene Type Synthetic Rubber 75-85 Durometer | |
AMS 3244 (B) | Flame Resistant Chloroprene Type Synthetic Rubber 65-75 Durometer | |
AMS 3248 (B) | Phosphate Ester Resistant Ethylene Propylene Type Synthetic Rubber 55-65 Durometer | |
AMS 3249 (B) | Hydrazine Base Fluid Resistant Ethylene Propylene Type Synthetic Rubber 75-85 Durometer | |
AMS 3260 (B) | General Purpose Ethylene Propylene Terpolymer Synthetic Rubber Sheet | |
AMS 3301 (B) | General Purpose Ethylene Propylene Terpolymer Synthetic Rubber Sheet | |
AMS 3302 (B) | General Purpose Silicone Rubber 45-55 Durometer | |
AMS 3303 (B) | General Purpose Silicone Rubber 55-65 Durometer | |
AMS 3304 (B) | General Purpose Silicone Rubber 65-75 Durometer | |
AMS 3305 (B) | General Purpose Silicone Rubber 75-85 Durometer | |
AMS 3306 | High Modulus Silicone Rubber 55-65 Durometer | |
AMS 3307 (B) | Non-Oil Resistant Low Compression Set Silicone Rubber 70-80 Durometer | |
AMS 3325 (B) | Fuel and Oil Resistant Fluorosilicone Rubber 55-65 Durometer | |
AMS 3326 (B) | Fuel and Oil Resistant Fluorosilicone Rubber 50-65 Durometer | |
AMS 3327 (B) | High Temp. Fuel and Oil Resistant Fluorosilicone (FVMQ) Rubber 70-80 Durometer | |
AMS 3328 (B) | Fuel and Oil Resistant Fluorosilicone (FVMQ) Rubber 35-45 Durometer | |
AMS 3329 (B) | Fuel and Oil Resistant, Fluorosilicone (FVMQ) Rubber 45-55 Durometer, High Strength | |
AMS 3330 (B) | Fuel and Oil Resistant, Fluorosilicone (FVMQ) Rubber 45-55 Durometer | |
AMS 3331 (B) | Fuel and Oil Resistant, Fluorosilicone (FVMQ) Rubber 65-75 Durometer | |
AMS 3334 (B) | Extreme Low Temperature Resistant Silicone Rubber 35-45 Durometer | |
AMS 3335 (B) | Extreme Low Temperature Resistant Silicone Rubber 45-55 Durometer | |
AMS 3336 (B) | Extreme Low Temperature Resistant Silicone Rubber 55-65 Durometer | |
AMS 3337 (B) | High and Extreme Low Temperature Resistant Silicone Rubber 65-75 Durometer | |
AMS 3338 (B) | High and Extreme Low Temperature Resistant Silicone Rubber 75-85 Durometer | |
AMS 3344 (B) | 1800psi Tensile Strength Silicone Rubber 45-55 Durometer | |
AMS 3345 (B) | 1000psi Tensile Strength Silicone Rubber 45-55 Durometer | |
AMS 3346 (B) | 1000psi Tensile Strength Silicone Rubber 55-65 Durometer | |
AMS 3347 (B) | High Modulus 1200psi Tensile Strength Silicone Rubber 45-55 Durometer | |
AMS 3348 (B) | High Resiliency 1150psi Tensile Strength Silicone Rubber | |
AMS 3349 (B) | High Resiliency 1100psi Tensile Strength Silicone Rubber 55-75 Durometer | |
AMS 3356 (B) | Lubricating Oil and Compression Set Resistant, Electrical Grade Silicone Rubber 55-65 Durometer | |
AMS 3357 (B) | Lubricating Oil and Compression Set Resistant Silicone Rubber 65-75 Durometer | |
AMS 7259 (B) | Very Low Compression Set High-Temperature-Fluid Resistant Fluorocarbon Rubber Sealing Rings 85-95 Durometer | |
AMS 7260 (B) | Fuel and Low Temperature Resistant Synthetic Rubber Packings Rings 70-80 Durometer | |
AMS 7263 (B) | Phosphate Ester Hydraulic Fluid Resistant, Butyl Type Synthetic Rubber Packing Rings 85-95 Durometer | |
AMS 7266 (B) | General Purpose High Temperature Fuel and Oil Resistant Fluorosilicone Rubber Sealing Rings | |
AMS 7267 (B) | Heat Resistant, Low Compression Set Silicone Rubber Sealing Rings 70-80 Durometer | |
AMS 7268 (B) | Non-Oil Resistant Low Compression Set Silicone Rubber Sealing Rings 65-75 Durometer | |
AMS 7269 (B) | Space and Vacuum Service Low Out Gassing Silicone Rubber Sealing Rings 45-55 Durometer | |
AMS 7270 (B) | Fuel Resistant Synthetic Rubber Sealing Rings 65-75 Durometer | |
AMS 7271 (B, P1) | Fuel and Low Temperature Resistant Synthetic Rubber Sealing Rings 60-70 Durometer | |
AMS 7272 (B) | Synthetic Lubricant Resistant NBR Type Synthetic Rubber Sealing Rings 65-75 Durometer | |
AMS 7273 (B) | High Temperature Fuel and Oil Resistant Fluorosilicone Rubber Sealing Rings 70-80 Durometer | |
AMS 7274 (B) | Oil Resistant Synthetic Rubber Sealing Rings 65-75 Durometer | |
AMS 7275 | Synthetic Lubricant Resistant Fluorocarbon Type Synthetic Rubber Sealing Rings 65-85 Durometer | |
AMS 7276 (B) | High-Temperature Fluid Resistant, Very Low Compression Set, Fluorocarbon Rubber Sealing Rings 70-80 Durometer | |
AMS 7277 | Phosphate Ester Hydraulic Fluid Resistant Butyl Type Synthetic Rubber Sealing Rings 70-85 Durometer | |
AMS 7278 (B) | High Temperature Fluid Resistant Fluorocarbon Type Synthetic Rubber Sealing Rings 70-80 Durometer NONCURRENT for new design AMS 7276 and AMS 7280 should be used where AMS 7278 material would have been suitable. | |
AMS 7279 (B) | High Temperature Fluid Resistant Fluorocarbon Type Synthetic Rubber Sealing Rings 85-95 Durometer | |
AMS 7280 (B) | High Temperature Fluid Resistant, Low Compression Set Fluorocarbon Rubber Sealing Rings 70-80 Durometer | |
A-A-59588 CL1A GR40 ZZ-R-765 (B) CL1A GR40(A-A-55801) | Silicone Rubber Specifications for 3 classes with various grades (durometers).Class 1a Low temperature resistant | |
A-A-59588 CL1A GR50 ZZ-R-765 (B) CL1A GR50(A-A-55801) | Silicone Rubber Specifications for 3 classes with various grades (durometers).Class 1a Low temperature resistant | |
A-A-59588 CL1A GR60 ZZ-R-765 (B) CL1A GR60(A-A-55801) | Silicone Rubber Specifications for 3 classes with various grades (durometers).Class 1a Low temperature resistant | |
A-A-59588 CL1A GR70 ZZ-R-765 (B) CL1A GR70(A-A-55801) | Silicone Rubber Specifications for 3 classes with various grades (durometers).Class 1a Low temperature resistant | |
A-A-59588 CL1A GR80 ZZ-R-765 (B) CL1A GR80(A-A-55801) | Silicone Rubber Specifications for 3 classes with various grades (durometers).Class 1a Low temperature resistant | |
A-A-59588 CL1B GR40 ZZ-R-765 (B) CL1B GR40(A-A-55801) | Silicone Rubber Specifications for 3 classes with various grades (durometers).Class 1b Low temperature resistant and low compression set high temperature | |
A-A-59588 CL1B GR50 ZZ-R-765 (B) CL1B GR50(A-A-55801) | Silicone Rubber Specifications for 3 classes with various grades (durometers).Class 1b Low temperature resistant and low compression set high temperature | |
A-A-59588 CL1B GR60 ZZ-R-765 (B) CL1B GR60(A-A-55801) | Silicone Rubber Specifications for 3 classes with various grades (durometers).Class 1b Low temperature resistant and low compression set high temperature | |
A-A-59588 CL1B GR70 ZZ-R-765 (B) CL1B GR70(A-A-55801) | Silicone Rubber Specifications for 3 classes with various grades (durometers).Class 1b Low temperature resistant and low compression set high temperature | |
A-A-59588 CL1B GR80 ZZ-R-765 (B) CL1B GR80(A-A-55801) | Silicone Rubber Specifications for 3 classes with various grades (durometers).Class 1b Low temperature resistant and low compression set high temperature | |
A-A-59588 CL2A GR40 ZZ-R-765 (B) CL2A GR40(A-A-55801) | Silicone Rubber Specifications for 3 classes with various grades (durometers).Class 2a High temperature resistant | |
A-A-59588 CL2A GR50 ZZ-R-765 (B) CL2A GR50(A-A-55801) | Silicone Rubber Specifications for 3 classes with various grades (durometers).Class 2a High temperature resistant | |
A-A-59588 CL2A GR60 ZZ-R-765 (B) CL2A GR60(A-A-55801) | Silicone Rubber Specifications for 3 classes with various grades (durometers).Class 2a High temperature resistant | |
A-A-59588 CL2A GR70 ZZ-R-765 (B) CL2A GR70(A-A-55801) | Silicone Rubber Specifications for 3 classes with various grades (durometers).Class 2a High temperature resistant | |
A-A-59588 CL2A GR80 ZZ-R-765 (B) CL2A GR80(A-A-55801) | Silicone Rubber Specifications for 3 classes with various grades (durometers).Class 2a High temperature resistant | |
A-A-59588 CL2B GR40 ZZ-R-765 (B) CL2B GR40(A-A-55801) | Silicone Rubber Specifications for 3 classes with various grades (durometers).Class 2b High temperature resistant and low compression set | |
A-A-59588 CL2B GR50 ZZ-R-765 (B) CL2B GR50(A-A-55801) | Silicone Rubber Specifications for 3 classes with various grades (durometers).Class 2b High temperature resistant and low compression set | |
A-A-59588 CL2B GR60 ZZ-R-765 (B) CL2B GR60(A-A-55801) | Silicone Rubber Specifications for 3 classes with various grades (durometers).Class 2b High temperature resistant and low compression set | |
A-A-59588 CL2B GR70 ZZ-R-765 (B) CL2B GR70(A-A-55801) | Silicone Rubber Specifications for 3 classes with various grades (durometers).Class 2b High temperature resistant and low compression set | |
A-A-59588 CL2B GR80 ZZ-R-765 (B) CL2B GR80(A-A-55801) | Silicone Rubber Specifications for 3 classes with various grades (durometers).Class 2b High temperature resistant and low compression set | |
MIL-G-1086 (B) Type I | Gasket Material, Synthetic Rubber for Bolted Steel Tanks. 70-80 durometer | |
MIL-G-1086 (B) Type II | Gasket Material, Synthetic Rubber for Bolted Steel Tanks. 45-55 durometer | |
MIL-PRF-1149 (B)(MIL-G-1149) TY I CL1 | 50 ± 5 Durometer Hardness Synthetic Rubber Gasket Materials - Oil resistant chloroprene polymer | |
MIL-PRF-1149 (B)(MIL-G-1149) TYI CL 2 | 50 ± 5 Durometer Hardness Synthetic Rubber Gasket Materials - Non-oil resistant styrene-butadiene copolymer (SBR) | |
MIL-PRF-1149 (B)(MIL-G-1149) TY I CL3 | 50 ± 5 Durometer Hardness Synthetic Rubber Gasket Materials - Phosphate ester resistant isoprene-isobutylene copolymer (Butyl) | |
MIL-PRF-1149 (B)(MIL-G-1149) TY I CL5 | 50 ± 5 Durometer Hardness Synthetic Rubber Gasket Materials - Fuel resistant acrylonitrile-butadiene copolymer (NBR) | |
MIL-PRF-1149 (B)(MIL-G-1149) TY II CL1 | 65 ± 5 Durometer Hardness Synthetic Rubber Gasket Materials - Oil resistant chloroprene polymer | |
MIL-PRF-1149 (B)(MIL-G-1149) TY II CL2 | 65 ± 5 Durometer Hardness Synthetic Rubber Gasket Materials - Non-oil resistant styrene-butadiene copolymer (SBR) | |
MIL-PRF-1149 (B)(MIL-G-1149) TY II CL3 | 65 ± 5 Durometer Hardness Synthetic Rubber Gasket Materials - Phosphate ester resistant isoprene-isobutylene copolymer (Butyl) | |
MIL-PRF-1149 (B)(MIL-G-1149) TY II CL5 | 65 ± 5 Durometer Hardness Synthetic Rubber Gasket Materials - Fuel resistant acrylonitrile-butadiene copolymer (NBR) | |
MIL-PRF-6855 (B)(AMS-R-6855( (B)(MIL-R-6855) (B)CL1 GR50 | Synthetic Rubber, Sheets, Strips, Molded or Extruded Shapes Low - Temperature Synthetic RubberClass 1 - Fuel and Petroleum oil resistant | |
MIL-PRF-6855 (B)(AMS-R-6855( (B)(MIL-R-6855) (B)CL1 GR60 | Synthetic Rubber, Sheets, Strips, Molded or Extruded Shapes Low - Temperature Synthetic RubberClass 1 - Fuel and Petroleum oil resistant | |
MIL-PRF-6855 (B)(AMS-R-6855( (B)(MIL-R-6855) (B)CL1 GR70 | Synthetic Rubber, Sheets, Strips, Molded or Extruded Shapes Low - Temperature Synthetic RubberClass 1 - Fuel and Petroleum oil resistant | |
MIL-PRF-6855 (B)(AMS-R-6855( (B)(MIL-R-6855) (B)CL2 TYA GR40 | Synthetic Rubber, Sheets, Strips, Molded or Extruded Shapes Low - Temperature Synthetic RubberClass 2 -Petroleum oil, weather and ozone resistantType A - High Ozone concentration | |
MIL-PRF-6855 (B)(AMS-R-6855( (B)(MIL-R-6855) (B)CL2 TYA GR50 | Synthetic Rubber, Sheets, Strips, Molded or Extruded Shapes Low - Temperature Synthetic RubberClass 2 -Petroleum oil, weather and ozone resistantType A - High Ozone concentration | |
MIL-PRF-6855 (B)(AMS-R-6855( (B)(MIL-R-6855) (B)CL2 TYA GR60 | Synthetic Rubber, Sheets, Strips, Molded or Extruded Shapes Low - Temperature Synthetic RubberClass 2 -Petroleum oil, weather and ozone resistantType A - High Ozone concentration | |
MIL-PRF-6855 (B)(AMS-R-6855( (B)(MIL-R-6855) (B)CL2 TYA GR70 | Synthetic Rubber, Sheets, Strips, Molded or Extruded Shapes Low - Temperature Synthetic RubberClass 2 -Petroleum oil, weather and ozone resistantType A - High Ozone concentration | |
MIL-PRF-6855 (B)(AMS-R-6855( (B)(MIL-R-6855) (B)CL2 TYA GR80 | Synthetic Rubber, Sheets, Strips, Molded or Extruded Shapes Low - Temperature Synthetic RubberClass 2 -Petroleum oil, weather and ozone resistantType A - High Ozone concentration | |
MIL-PRF-6855 (B)(AMS-R-6855( (B)(MIL-R-6855) (B)CL2 TYB GR40 | Synthetic Rubber, Sheets, Strips, Molded or Extruded Shapes Low - Temperature Synthetic RubberClass 2 -Petroleum oil, weather and ozone resistantType B - Low Ozone concentration | |
MIL-PRF-6855 (B)(AMS-R-6855( (B)(MIL-R-6855) (B)CL2 TYB GR50 | Synthetic Rubber, Sheets, Strips, Molded or Extruded Shapes Low - Temperature Synthetic RubberClass 2 -Petroleum oil, weather and ozone resistantType B - Low Ozone concentration | |
MIL-PRF-6855 (B)(AMS-R-6855( (B)(MIL-R-6855) (B)CL2 TYB GR60 | Synthetic Rubber, Sheets, Strips, Molded or Extruded Shapes Low - Temperature Synthetic RubberClass 2 -Petroleum oil, weather and ozone resistantType B - Low Ozone concentration | |
MIL-PRF-6855 (B)(AMS-R-6855( (B)(MIL-R-6855) (B)CL2 TYB GR70 | Synthetic Rubber, Sheets, Strips, Molded or Extruded Shapes Low - Temperature Synthetic RubberClass 2 -Petroleum oil, weather and ozone resistantType B - Low Ozone concentration | |
MIL-PRF-6855 (B)(AMS-R-6855( (B)(MIL-R-6855) (B)CL2 TYB GR80 | Synthetic Rubber, Sheets, Strips, Molded or Extruded Shapes Low - Temperature Synthetic RubberClass 2 -Petroleum oil, weather and ozone resistantType B - Low Ozone concentration | |
MIL-PRF-6855 (B)(AMS-R-6855( (B)(MIL-R-6855) (B)CL3 GR60 | Synthetic Rubber, Sheets, Strips, Molded or Extruded Shapes Low - Temperature Synthetic RubberClass 3 -Non-oil resistant | |
MIL-PRF-6855 (B)(AMS-R-6855( (B)(MIL-R-6855) (B)CL3 GR70 | Synthetic Rubber, Sheets, Strips, Molded or Extruded Shapes Low - Temperature Synthetic RubberClass 3 -Non-oil resistant | |
MIL-PRF-6855 (B)(AMS-R-6855( (B)(MIL-R-6855) (B)CL3 GR80 | Synthetic Rubber, Sheets, Strips, Molded or Extruded Shapes Low - Temperature Synthetic RubberClass 3 -Non-oil resistant | |
MIL-R-6891 | Anodic Rubber | |
MIL-H-7083 | Nonflammable water-base hydraulic fluid for aircraft use. | |
JIS B 2401 (T) Class 1A | Japanese Industrial Standard O-Rings | |
JIS B 2401 (T) Class 1B | Japanese Industrial Standard O-Rings | |
JIS B 2401 (T) Class 2 | Japanese Industrial Standard O-Rings | |
JIS B 2401 (T) Class 3 | Japanese Industrial Standard O-Rings | |
JIS B 2401 (T) Class 4C | Japanese Industrial Standard O-Rings | |
JIS B 2401 (T) Class 4D | Japanese Industrial Standard O-Rings | |
SAE J 515 Type 1 | Hydraulic O-Ring Sizes correspond with AS 568 straight thread tube fitting boss gaskets:- Petroleum base and nonflammable waterbase hydraulic fluids 85-95 durometer. | |
SAE J 515 Type 2 | Hydraulic O-Ring Sizes correspond with AS 568 straight thread tube fitting boss gaskets:- Nonflammable phosphate ester base hydraulic fluid 75-85 durometer. | |
SAE J 515 Type 3 | Hydraulic O-Ring Sizes correspond with AS 568 straight thread tube fitting boss gaskets:- High Temperature for Hydraulic Fluids 85 -95 Durometer | |
MIL-R-7362 TYI | Diester Synthetic Oil Resistant Synthetic RubberType I - O-Rings | |
MIL-R-7362 TYII | Diester Synthetic Oil Resistant Synthetic RubberType II - Molded parts, sheets, strips and extruded parts | |
MIL-L-7808 | Synthetic Base Aircraft Turbine Engine Lubricating Oil | |
MIL-A-8243 | Anti-Icing and Deicing-Defrosting Fluid | |
MIL-H-8446 | Aircraft Non-Petroleum Base Hydraulic Fluid | |
MIL-C-8603 | Support Loop Type Clamps for electrical wire bundles and other non-hydraulic uses | |
MIL-S-8660 | Silicone, Compound NATO Code Number S-763 | |
MIL-R-8791 | Tetrafluoroethylene resin (TFE) retainers intended for use in hydraulic and pneumatic system components as anti-extrusion devices in conjunction with packings and gaskets | |
MIL-R-8913 TY I | Piston Rod Wiper Ring Sizes per MS 28903.Type I - Rubber rings | |
MIL-R-8913 TYII | Piston Rod Wiper Ring Sizes per MS 28903.Type II - Polytetrafluoroethylene rings (PTFE) | |
MIL-R-8913 TYIII | Piston Rod Wiper Ring Sizes per MS 28903.Type III - Metallic rings | |
MS 9020 (P2) | Twenty O-ring sizes. Dash numbers correspond with AS 568 straight thread tube fitting boss gaskets (900 series). Material per AMS 7271. | |
MS 9021 (P2) | Three-hundred and twenty O-ring sizes. Dash numbers correspond with AS 568 series. Material per AMS 7271. | |
MS 9058 | Scarf cut split Back-up rings. Eighteen sizes for straight thread tube fitting boss gaskets (900 series). Material is PTFE per AMS 3651. | |
MS 9068 (P2) | Two-hundred and twenty-nine O-ring sizes. Dash numbers correspond to AS 568. Material is a 65-75 durometer silicone rubber per AMS 3304. | |
MS 9136 | Engine Accessory Drive Gasket Asbestos and synthetic rubber. | |
MS 9203 | Metal O-ring, .094” tube by .006” wall. | |
MS 9204 | Metal O-ring, .094” tube by .010” wall. | |
MS 9205 | Metal O-ring, .125” tube by .010” wall. | |
MS 9241 (P1, A4) | Three-hundred and fifty-nine standard O-ring sizes. Dash numbers correspond to AS 568. Material is a 65-75 durometer nitrile per AMS 7272. | |
MS 9355 (P1) | Twenty standard O-ring sizes. Dash numbers correspond to AS 568 straight thread tube fitting boss gaskets (900 series). Material is a 65-75 durometer nitrile per AMS 7272. | |
MS 9373 | Silver plated metal O-Ring: .062” tube by .010” wall. | |
MS 9374 | Silver plated metal O-Ring: .094” tube by .006” wall. | |
MS 9375 | Silver plated metal O-Ring: .094” tube by .010” wall. | |
MS 9376 | Silver plated metal O-Ring: .125” tube by .010” wall. | |
MS 9385 | Twenty standard O-ring sizes. Dash numbers correspond to AS 568 straight thread tube fitting boss gaskets (900 series). Material is a 70-80 durometer silicone per AMS 7267. | |
MS 9386 | Three-hundred and fifty-nine standard O-ring sizes. Dash numbers correspond to AS 568. Material is a 70-80 durometer silicone per AMS 7267. | |
MS 9387 (P1) | Twenty standard O-ring sizes. Dash numbers correspond to AS 568 straight thread 9746 tube fitting boss gaskets (900 series) but tolerances are not as large. Material is a 70-80 durometer fluorocarbon per AMS 7278. | |
MS 9388 (P1) | Three-hundred and fifty-nine standard O-ring sizes. Dash numbers correspond to AS 568, but tolerances are not as large. Material is a 70-80 durometer fluorocarbon per AMS 7278. | |
MS 9484 | Eighteen sizes of scarf cut split Back-up rings for straight thread tube fitting boss gaskets. Material is polytetrafluoroethylene (PTFE) per AMS 3651. | |
MIL-Q-9858 | Quality Program Requirements | |
MS 9966 (P1) | Twenty standard O-ring sizes. Dash numbers correspond to AS 568 straight thread tube fitting boss gaskets (900 series). Material is a 70-80 durometer Fluorosilicone rubber per AMS 7273. | |
MS 9967 (P1) | Three-hundred and fifty-nine standard O-ring sizes. Dash numbers correspond to AS 568. Material is a 70-80 durometer Fluorosilicone rubber per AMS 7273 | |
MS 9968 (P1) | Internal Straight Thread Boss Material 70-80 durometer fluorocarbon per AMS 7280. | |
MS 9970 (P1) | Three-hundred and fifty-nine standard size O-rings. Dash numbers correspond to AS 568, but tolerances are not as large. Material is an 85-95 durometer fluorocarbon rubber per AMS 7279. | |
ISO 10423 | Petroleum and natural gas industries -- Drilling and production equipment -- Wellhead and christmas tree equipment. | |
MIL-L-10547 | Flexible Water-Vaporproof or Waterproof Case Liners. Overwraps and Sheets | |
MIL-F-10870 | Insulated Food Container with Inserts Elastomeric gasket per MIL-R-3065 and ASTM D2000. | |
MIL-G-10924 | Automotive and Artillery Grease | |
ISO 10993 | Biological evaluation of medical devices A twenty part series of standards. | |
MIL-R-11512 | Synthetic rubber seals for pure petroleum insulating oil. | |
MIL-P-11719 | Preformed Rubber Packing for use with Pneumatic Hose Couplings | |
MIL-G-12803 | Non-metallic Gasket Material Does not cover molded gaskets. | |
MIL-M-12863 | Vibration Mounts | |
MIL-G-13210 | Rubber Gaskets intended for use in making gas-tight connections in the assembly of gas mask canisters. | |
ISO 13485 | Medical devices - Quality management systems - Requirements for regulatory purposes | |
MIS 13937 TYI | Ethylene Propylene Rubber Sheets, Molded and Cut ShapesType I - Molded sheets or parts | |
MIS 13937 TYII | Ethylene Propylene Rubber Sheets, Molded and Cut ShapesType II - Precision molded O-rings, gaskets and packing | |
MIS 13937 TYIII | Ethylene Propylene Rubber Sheets, Molded and Cut ShapesType III - Extruded molds | |
ISO 14001 | Environmental management systems -- Requirements with guidance for use | |
MIL-C 14055 (Q) | Synthetic Rubber Hydraulic Brake Actuating Cylinder Cup | |
MIL-R-14328 | General Purpose Gasket Material (for Extreme Climatic Conditions) Medium Soft Synthetic Rubber Sheet | |
MIL-P-14401 | Vehicular Personnel-Protection Cushioning Pads | |
ISO 14644 | Cleanrooms and associated controlled environments A nine part series of standards. | |
MIL-P-14574 | Cloth Insertion Synthetic Rubber Packing (Wiper Ring) Fiber reinforced rubber rod wiper. | |
MIL-R-15624 CL1 | Medium soft synthetic rubber for shipboard gasket use except low temperature application.Class 1 - Chloroprene | |
MIL-R-15624 CL2 | Medium soft synthetic rubber for shipboard gasket use except low temperature application.Class 2 - Butadiene-styrene (SBR) | |
MIL-R-15624 CL3 | Medium soft synthetic rubber for shipboard gasket use except low temperature application.Class 3 - Butadiene-acrylonitrile (NBR) | |
MS 17413 (P1) | Two hundred and thirty-nine standard size O-rings. Dash numbers to AS 568. Material is a 70-80 durometer fluorocarbon rubber per AMS 7278. | |
MIL-G-17553 (Q) | O-Ring Gasket for Rockets | |
MIL-D-17650 | Insert Type Rubber Valve Disk | |
MIL-P-18484 | Synthetic Rubber Hydraulic-Seal Preformed Packing | |
MIL-G-18586 (Q) CL1 | Shipboard Electrical Junction Box O-ring Gaskets -20°F and above.Class 1 - Butadiene-styrene copolymer (non-oil resistant) | |
MIL-G-18586 (Q) CL2 | Shipboard Electrical Junction Box O-ring Gaskets -20°F and above.Class 2 - Butadiene-acrylonitrile copolymer (oil resistant) | |
MIL-P-19152 | High Pressure Hydraulic Packings (for Hydropneumatic Systems) | |
MIL-H-19457 | Non-Neurotoxic Fire-Resistant Hydraulic Fluid | |
MIL-G-19655 | High-pressure gasket material for use where petroleum or phosphate ester hydraulic fluids are used. | |
MIL-G-19769 | Slide Valve Oil Resistant Synthetic Rubber Gaskets | |
MIL-P-19918 | V-Ring Packing material and Filler Ring Material. | |
MIL-S-21558 | Oil, Plain or Plain Encase Seals | |
MIL-G-21569 (B) CLII | Synthetic Rubber Cylinder Liner Seal GasketsClass I - Oil resistant 55-75 durometer butadiene and acrylonitrlie copolymer | |
MIL-G-21569 (B) CLII | Synthetic Rubber Cylinder Liner Seal GasketsClass II - High temperature resistant 55-75 durometer elastomeric polysiloxanes | |
MIL-G-21610 (B) TYII | Synthetic rubber gaskets of various cross sections for use in heat exchangers, 60-75 durometer.Type II - Elastomeric Polysiloxanes base material | |
MIL-S-21923 | Ozone Resistant Butadiene-Styrene Type Synthetic Rubber Compound for Low Temperature Service | |
MIL-G-22004 | Lighting Fixture High Temperature Gasket | |
MIL-G-22050 (B) GR1 | Rubber Gasket, Packing Seals and Sheet Rubber Material, for use with Polar Fluids, Steam and Air at Moderately High TemperaturesGrade 1 - 60-70durometer hardness | |
MIL-G-22050 (B) GR2 | Rubber Gasket, Packing Seals and Sheet Rubber Material, for use with Polar Fluids, Steam and Air at Moderately High TemperaturesGrade 2 - 75-85 durometer hardness durometer hardness | |
MIL-G-22050 (B) GR3 | Rubber Gasket, Packing Seals and Sheet Rubber Material, for use with Polar Fluids, Steam and Air at Moderately High TemperaturesGrade 3 - 85-95 durometer hardness | |
MIL-S-23190 | Plastic Straps, Clamps and Mounting Hardware for Cable Hardness Tying and Support | |
MIL-M-23573 | This specification covers chelated-Monethanolamine (MEA) for use in equipment for the removal of carbon dioxide from the air using a regenerative absorption process. | |
MIL-G-23652 TYI | Rubber gasket and packing material intended for use in 300psig hydraulic systems. The material is compatible with both petroleum base fluids and phosphate ester fluid Specification requires either color coding of parts or individual packaging.Type I - for use in hydraulic systems up to 300psig pressure 65-75 durometer | |
MIL-G-23652 TYII | Rubber gasket and packing material intended for use in 300psig hydraulic systems. The material is compatible with both petroleum base fluids and phosphate ester fluid Specification requires either color coding of parts or individual packaging.Type II - for use in hydraulic systems up to 5200psig pressure 85-95 durometer. | |
ISO 239236-2 | Petroleum, petrochemical and natural gas industries -- Non-metallic materials in contact with media related to oil and gas production -- Part 2: Elastomers (under development) | |
MIL-I-24063 | Insert Sets, Sound Isolation for RISIC-I Flexible Connectors | |
MS 24690 (Q) | Preformed High Pressure Air Valve Packing One size only, 0.070” c/s x 0.551” ID. Material per MIL-P-5516, Class B. | |
MIL-P-25732 (Q)MIL-R-25897(Obsolete) TYI CLI | O-Ring packings for use with petroleum based hydraulic fluid over the temperature range of 65° to 275°F. Sizes conform to MS 28775 (same as AS 568 dash numbers). High Temperature Fluid Resistant Fluorocarbon Elastomeric RubberType I - O-Ring and compression seals, Class I (70-80 durometer) | |
MIL-P-25732 (Q)MIL-R-25897(Obsolete) TYI CLII | O-Ring packings for use with petroleum based hydraulic fluid over the temperature range of 65° to 275°F. Sizes conform to MS 28775 (same as AS 568 dash numbers). High Temperature Fluid Resistant Fluorocarbon Elastomeric RubberType I - O-Ring and compression seals, Class II (85-95 durometer) | |
MIL-P-25732 (Q)MIL-R-25897(Obsolete) TYII CLI | O-Ring packings for use with petroleum based hydraulic fluid over the temperature range of 65° to 275°F. Sizes conform to MS 28775 (same as AS 568 dash numbers). High Temperature Fluid Resistant Fluorocarbon Elastomeric RubberType II - Molded parts (other than sealing devices) sheets, strips and extruded shapes, Class I (70-80 durometer) | |
MIL-P-25732 (Q)MIL-R-25897(Obsolete) TYII CLII | O-Ring packings for use with petroleum based hydraulic fluid over the temperature range of 65° to 275°F. Sizes conform to MS 28775 (same as AS 568 dash numbers). High Temperature Fluid Resistant Fluorocarbon Elastomeric RubberType II - Molded parts (other than sealing devices) sheets, strips and extruded shapes, Class II (85-95 durometer) | |
AMR-R-25988(MIL-R-25988) (B)(MIL-DTL-25988) (B)TYI CL1 GR60 | Oil and Fuel Resistant Fluorosilicone Elastomer Rubber Sheets, Strips, Molded Parts and Extruded Shapes. Type I - O-Rings | |
AMR-R-25988(MIL-R-25988) (B)(MIL-DTL-25988) (B)TYI CL1 GR70 | Oil and Fuel Resistant Fluorosilicone Elastomer Rubber Sheets, Strips, Molded Parts and Extruded Shapes. Type I - O-Rings | |
AMR-R-25988(MIL-R-25988) (B)(MIL-DTL-25988) (B)TYI CL1 GR80 | Oil and Fuel Resistant Fluorosilicone Elastomer Rubber Sheets, Strips, Molded Parts and Extruded Shapes. Type I - O-Rings | |
AMR-R-25988(MIL-R-25988) (B)(MIL-DTL-25988) (B)TYII CL1 GR40 | Oil and Fuel Resistant Fluorosilicone Elastomer Rubber Sheets, Strips, Molded Parts and Extruded Shapes. Type II - Other Molded Parts, Class 1 -general purpose | |
AMR-R-25988(MIL-R-25988) (B)(MIL-DTL-25988) (B)TYII CL1 GR50 | Oil and Fuel Resistant Fluorosilicone Elastomer Rubber Sheets, Strips, Molded Parts and Extruded Shapes. Type II - Other Molded Parts, Class 1 -general purpose | |
AMR-R-25988(MIL-R-25988) (B)(MIL-DTL-25988) (B)TYII CL1 GR60 | Oil and Fuel Resistant Fluorosilicone Elastomer Rubber Sheets, Strips, Molded Parts and Extruded Shapes. Type II - Other Molded Parts, Class 1 -general purpose | |
AMR-R-25988(MIL-R-25988) (B)(MIL-DTL-25988) (B)TYII CL1 GR70 | Oil and Fuel Resistant Fluorosilicone Elastomer Rubber Sheets, Strips, Molded Parts and Extruded Shapes. Type II - Other Molded Parts, Class 1 -general purpose | |
AMR-R-25988(MIL-R-25988) (B)(MIL-DTL-25988) (B)TYII CL2 GR50 | Oil and Fuel Resistant Fluorosilicone Elastomer Rubber Sheets, Strips, Molded Parts and Extruded Shapes. Type II - Other Molded Parts, Class 2 -high-strength general purpose | |
MIL R-25988/1 (B) | Grade 70 Class 1 O-Rings Oil and Fuel-Resistant Fluorosilicone Elastomer Rubber | |
MIL-R-25988/2 (B) | Grade 70 Class 3 O-Rings Oil and Fuel-Resistant Fluorosilicone Elastomer Rubber | |
MIL-R-25988/3 (B) | Grade 60 Class 1 O-Rings Oil and Fuel-Resistant Fluorosilicone Elastomer Rubber | |
MIL-R-25988/4 (B) | Grade 80 Class 1 O-Rings Oil and Fuel-Resistant Fluorosilicone Elastomer Rubber | |
MS 26577 | Airport Marker Light Base Gasket Material is a heat resistant silicone rubber per ZZ-R-765 Class 2a, Grade 80. | |
MS 27030 | Gasket-Coupling half, Quick Disconnect, Cam-locking Type 10 sizes, flat gaskets. | |
MS 27198 | Metal retainer with molded in rubber seal, material per MIL-R-25988. | |
MS 27290 | Cable Adapter Bushing Material is a silicone rubber per MIL-R-5847 Class 2b, Grade 50. | |
MS 27488 | Electric Connector Sealing Plug | |
MS 27595 | Tetrafluoroethylene Continuous Ring Packing Backing Retainer One-hundred and sixty-four sizes for standard O-Rings. Material per MIL-R-8791 Rectangular cross section. | |
MS 27595 | D-Ring Preform Packing Shock Strut material per MIL-P-5516. | |
MS 28773 | Straight Thread Tube Fitting Boss Tetrafluoroethylene Packing Backup Retainer cross section. Material per MIL-R-8791. | |
MS 28774 | Tetrafluoroethylene Single Turn Packing Backup Retainer One-hundred and sixty-four sizes of 22 degree scarf cut backups for standard O-Ring sizes. Rectangular cross section, material per MIL-R-8791. | |
MS28775 (Q) | Three-hundred and fifty-nine standard O-ring sizes. Dash numbers correspond with AS 568. Material is a 68+ durometer nitrile per MIL-P-25732. | |
MS 28776 | Piston Rod Scraper Many of the 71 dash sizes are manufactured in the dimensional style but not to the material specification in both 70 and 90 durometer nitrile. | |
MS 28777 | Aircraft Hydraulic Packing Backup Washer Thirteen sizes of uncut rectangular cross section backups for 900 series O-rings. Material specified is leather. We can supply in Teflon. | |
MS 28778 (Q) | Straight Thread Tube Fitting Boss Preformed Packing Dash numbers correspond with AS 568 straight thread tube fitting boss gaskets (900 series) Material per MIL-P-5510. | |
MS 28782 | Teflon Backup Packing Retainer Eighty-eight sizes of spiral cut, double turn backups, dash numbers correspond to the dash numbers of AN 6227 packings. Material per MIL-R-8791 | |
MS 28783 | Teflon Backup Gasket Ring Twenty-five sizes of spiral cut double turn backup rings. Dash numbers correspond to AN 6230 gaskets. Material per MIL-R-8791. | |
MS 28784 | Canceled. Superseded by MS 28775. | |
MS 28900 | Preformed Packings for Electrical Use Material is a 65-75 durometer chloroprene per AMS 3209 | |
MS 28903 | Hydraulic and Pneumatic Piston Rod Dirt Wiper Ring Material per MIL-R-8913. | |
MS 29512 | Fuel Resistant Straight Thread Tube Fitting Boss Gasket Thirteen standard size Orings. Dash numbers correspond to AS 568 straight thread tube fitting boss gaskets (900 series), Material per MIL-P-5315. | |
MS 29513 (Q) | Hydrocarbon Fuel Resistant Packing O-Ring One-hundred and seventy-four standard size O-rings. Dash numbers correspond to AS 568. Material per MIL-P-5315. | |
MS 29531 | Aircraft Engine Exhaust Port Closure Plug Material per MIL-R-6855 Class I or II Grade 40, Color yellow. | |
MS 29561 (P2) | Synthetic Lubricant Resistant Preformed O-Ring Packing One-hundred ninety-one standard size O-rings. Dash numbers correspond to AS 568. Material is a 65-75 durometer nitrile per MIL R-7362 Type I. | |
MS 33649 | Straight Thread Tube Fitting Boss Gasket Gland Dimensions | |
MS 33666 | Range of Sizes Aeronautical Elastomer Preformed Packing Two-hundred and fifty-six standard size O-rings. Dash numbers correspond to AS 568. No material specification. | |
MS 33675 | Packing Gland Ring Scrapper Installation No material specification. | |
MS 33688 | Range of Sizes Elastomeric Tube Fitting Preformed Packing Twenty standard dash sizes for straight thread tube fitting boss gaskets (900 series). No material specification. | |
MS 35133 | Preformed Packing Five dash sizes inactive for design after 11/6/64. | |
MS 35489 | Hot Oil and Coolant Resistant Rubber Grommet Material 50 durometer nitrile per MIL-STD-417 Grade SB-515-A1, B1, C2, D3, F2. | |
MS 35769 | Copper and Asbestos Annular Metallic-Encased Gasket | |
MS 35796 | Hot Galvanized (Pole-Line) Thimble Eye (Straight) Bolt | |
MS 35803 (Q) | Leather Backup Ring Packing Retainer Material per MIL-R-5521. | |
MIL-S-45005 | Spring-loaded single and multiple lip oil seal. The seal incorporates either a leather or synthetic elastomer sealing member | |
MIL-I-45208 | Inspection System Requirements | |
MIL-C-45662 | Calibration System Requirements | |
MIL-R-46089 | Closed Cell Silicone Sponge Rubber | |
MIL-L-46167 (Q) | Arctic Internal Combustion Engine Lubricating Oil | |
MIL-H-46170 | Fire Resistant Rush Inhibited Synthetic Hydrocarbon Base Hydraulic Fluid | |
MIL-B-46176 | Operational and Preservation Automotive All Weather Silicone Brake Fluid | |
NF T47-501 | Rubber O-Ring – Designation, sizes and tolerances. Published by AFNOR, the French standards association | |
MIL-C-50072 | Voicemitter-Outlet Valve Cover | |
MS 51920 | Steel encased rod seals. | |
MIL-S-52000 | Synthetic Rubber Gasket | |
MIL-C-52211 | Packing of Components and Assemblies for Industrial Gas | |
A-A-55801 | Silicone Rubber Specifications for 3 classes with various grades (durometers). See A-A-59588 (below) | |
MIL-R-83248 (B) TYI CL1 | High Temperature, Fluid and Compression Set Resistant, Fluorocarbon Elastomer RubberType I - O-rings and compression seals Class 1 - 70-80 durometer | |
MIL-R-83248 (B) TYI CL2 | High Temperature, Fluid and Compression Set Resistant, Fluorocarbon Elastomer RubberType I - O-rings and compression seals Class 2 - 85-95 durometer | |
MIL-R-83248 (B) TYII CL1 | High Temperature, Fluid and Compression Set Resistant, Fluorocarbon Elastomer RubberType II - Molded parts (other than sealing devices) sheets, strips and extruded shapes. Class 1 - 70-80 durometer | |
MIL-R-83248 (B) TYII CL2 | High Temperature, Fluid and Compression Set Resistant, Fluorocarbon Elastomer RubberType II - Molded parts (other than sealing devices) sheets, strips and extruded shapes. Class 2 - 85-95 durometer | |
MIL-R-83248/1 | Rubber, Fluorocarbon Elastomer, High Temperature, Fluid and Compression Set Resistant, O-Rings, Class 1, 75 Durometer | |
MIL-R-83248/2 | Rubber, Fluorocarbon Elastomer, High Temperature, Fluid and Compression Set Resistant, O-Rings, Class 2, 90 Durometer | |
MIL-R-82385 CLI | General Purpose Ethylene-Propylene RubberClass I - 60-70 durometer hardness | |
MIL-R-82385 CLII | General Purpose Ethylene-Propylene RubberClass II - 85-95 durometer hardness | |
MIL-R-83322 | Nitrogen Tetroxide (N204) Resistant Carboxy-Nitroso Rubber | |
MIL-R-83397 | Humidity Resistant Castable Polyurethane Rubber | |
MIL-R-83412 TYI | Hydrazine Resistant Ethylene-Propylene RubberType I - Seal Material | |
MIL-R-83412 TYII | Hydrazine Resistant Ethylene-Propylene RubberType II - Bladder and diaphragm material | |
MIL-R-83412 TYIII | Hydrazine Resistant Ethylene-Propylene RubberType III - Valve seal materia | |
MIL-P-83461(Q, B) | Petroleum Hydraulic Fluid Resistant Preformed Packing Improved Performance at 275°F (136°C) | |
MS 83461 (Q) | Standard O-ring sizes corresponding to AS 568. Material per MIL P-83461. | |
AMS-R-83485 (B)(MIL-P-83485) (B) | Fluorocarbon, Improved Performance at Low Temperature | |
MIL-P-87175 (Q) GR70 | Petroleum Hydraulic Fluid Resistant Phosphonitrilic Fluoroelastomer Preformed PackingGrade 70 65-75 durometer | |
MIL-P-87175 (Q) GR80 | Petroleum Hydraulic Fluid Resistant Phosphonitrilic Fluoroelastomer Preformed PackingGrade 80 75-85 durometer | |
A-A-55549(MS 90064) | ||
MS 90065 | Gaskets (Rectangular, for use with Waveguide Flanges) Material unless otherwise specified is a silicone per MIL-R-5847 Class 2b, Grade 50. | |
AN 123020 | Aluminum-Asbestos Annular Gaskets | |
AN 123851thru (B)AN 123950 | One hundred standard size O-rings. Sizes correspond with AS 568 but numbers are different. Material is a 65-75 durometer nitrile per AMS 7274. | |
AN 123951thru (B)AN 124050 | One-hundred standard size O-rings. Sizes correspond with AS 568 but numbers are different. Material is a 65-75 durometer nitrile per AMS 7270. | |
AS 568A | Standardized dash numbering system for O-Rings. Dimensions for 379 sizes are published as the minimum and maximum cross section and inside diameter for each dash number and expressed both in millimeters and inches. | |
AS 871 | O-Ring dimensional inspection guide. | |
MIL-STD-2073 | Standard Practice for Military Packaging | |
AIR 63 | O-Ring Size and Part Number Cross Reference Chartreferences many of the O-Ring sizes found on the various drawings: CKCX2CKCX3AS568AN6227AN 6230MX9021MS28775MS28784MS29513AN123870AN12391AN123970AN124014 | |
NORSOK M-710 | Qualification of non-metallic sealing materials and manufacturers | |
MIL-R-3065 | Fabricated Rubber Products Establishes the requirements for fabricated products of synthetic rubber together with procedures for the inspection of such products. Any material specification is per MIL-STD-417 nomenclature. | |
CLHX3 | Old Canceled Oil Seal Spec - metal encased seal with spring-loaded leather or neoprene sealing member. | |
SAE J 14 | Canceled. Superseded by SAE J200 and ASTM D2000. | |
AFLCM71 | Preservation, Packaging methods and instructions for coding. | |
AN-P-79 | Superseded by MIL-P-5516B O-Rings class B Nitrile. | |
AIR 81 | Hydraulic Fluid Characteristics | |
Fed. Std. 90 | Describes the principle synthetic rubber specification limits sampling and testing. | |
MIL-STD-100 | Engineering Drawing Practices | |
MIL-STD-105 | Sampling Procedures and Tables for Inspection by Attributes | |
H 106 | Multi-Level continuous sampling procedures and instructions for selection and administration of sampling inspection procedures | |
H 107 | Single-Level Continuous Sampling Procedures and Tables for Inspection by Attributes | |
MIL-P-116 | Methods of Preservation to protect against corrosion, mechanical and physical damage. | |
MIL-B-117 | Heat sealable, interior packaging bags, sleeves and tubing required by Military Services for the protection of supplies | |
SAE J 120 Class I (Obsolete) | Rubber Automotive Applications Dash numbers correspond with AS 568 series. Dash number “R1” denotes O-rings;”R2” denotes square cross-section rings.- Oil resistant service | |
SAE J 120 Class II (Obsolete) | Rubber Automotive Applications Dash numbers correspond with AS 568 series. Dash number “R1” denotes O-rings;”R2” denotes square cross-section rings.- Gasoline Resistant service | |
MIL-P-121 | Flexible, greaseproofed, waterproofed barrier material used for protection of supplies and equipment during transportation and storage. | |
MIL-STD-129 | Marking for Shipment and Storage | |
MIL-STD-130 | Identification Marking of US Military Property | |
MIL-HDBK-149 | Rubber 500 page Handbook of Rubber Properties. | |
HH-P-151 | Cloth-Insert Rubber-Sheet Packing Intended for flange joints for water or brine services up to 250 pounds pressure and ventilating systems. | |
HH-G-156 Type I | General Purpose Rubber Gasket Material.- Soft 35-45 durometer | |
HH-G-156 Type II | General Purpose Rubber Gasket Material.- Medium 50-60 durometer | |
HH-G-156 Type III | General Purpose Rubber Gasket Material.- Hard 75-85 durometer | |
MIL-STD-177 | Terms for Visible Defects of Rubber Products | |
NACE TM 0187 | Standard test Method for Evaluating Elastomeric Materials in Sour Gas Environments | |
SAE J200 | Classification System for Rubber Materials for Automotive Applications Same nomenclature system as ASTM D2000. See ASTM D2000 for more details. | |
MIL-STD-289 | Visual Inspection Guide for Rubber Sheet Material | |
Mil-STD-298 | Visual Inspection Guide for Rubber Extruded Goods | |
L-P-390 | Polyethylene and copolymers for general purpose, dielectric and weather resistant uses in low, medium and high density. | |
MIL-STD-407 | Visual Inspection Guide for Rubber Molded Items | |
MIL-STD-413 | Visual Inspection Guide for Rubber Molded O-Rings | |
MIL-STD-417 | Nomenclature system for specifying the properties of a wide range of compounds with Nomenclature system for specifying the properties of a wide range of compounds with | |
MIL-G-432 | Synthetic Rubber Gaskets-Nonmetallic Five types of synthetic rubber gaskets. | |
ANA 438 | Canceled. Superseded by MIL-STD-1523. | |
MIL-STD-454 | Standard General Requirements for Electronic Equipment | |
TT-C-490 | Cleaning Methods for Ferrous Surfaces & Pretreating for Organic Coatings | |
L-P-512 | Requirements for Polyethylene Sheets. | |
SAE J 514 | Straight Thread Tube Fitting Boss Gasket Gland Dimensions | |
L-P-590 | Requirements for Polyethylene Molding and Extrusion Plastic Compounds | |
FED-STD-601 | Federal Test Method standard for sampling and testing rubber. | |
NAS 617 | Thirteen standard size O-rings. Dash numbers correspond with AS 568 straight thread tube fitting boss gaskets (900 series). Material 65-75 durometer nitrile per MIL-R-7362 Type 1, Composition A. | |
MIL-STD-670 | Classification System and Tests for Cellular Elastomeric Materials | |
MIL-HDBK-695 | Shelf storage of rubber products. | |
AS 708 | Special O-ring surface condition requirements (top quality). | |
ZZ-R-710 | Vulcanized rubber gasket material of 35 durometer hardness | |
MIL-STD-726 | Packaging Requirements Code | |
ASTM D735 | Canceled. Superseded by SAE J200 and ASTM D2000. | |
TT-S-735 Type I | Hydrocarbon Standard Test Fluids Supersedes MIL-S-3136B- Iso-octane (ASTM Ref. Fuel A) | |
TT-S-735 Type II | Hydrocarbon Standard Test Fluids Supersedes MIL-S-3136B. Iso-octane and aromatic mixture | |
TT-S-735 Type III | Hydrocarbon Standard Test Fluids Supersedes MIL-S-3136B. Iso-octane and toluene mixture (ASTM Ref. Fuel B) | |
TT-S-735 Type IV | Hydrocarbon Standard Test Fluids Supersedes MIL-S-3136B. Petroleum base oil, low swell characteristics (ASTM Oil #1) | |
TT-S-735 Type V | Hydrocarbon Standard Test Fluids Supersedes MIL-S-3136B. Petroleum base oil, medium swell characteristics (ASTM Oil #2) | |
TT-S-735 Type VI | Hydrocarbon Standard Test Fluids Supersedes MIL-S-3136B. Petroleum base oil, high swell characteristics (ASTM Oil #3) | |
TT-S-735 Type VII | Hydrocarbon Standard Test Fluids Supersedes MIL-S-3136B. Cyclohexane and aromatic mixture (Mercaptan added) | |
AS 757 | Straight thread boss dimensions. | |
MIL-STD-1188 | Commercial Packaging of Supplies and Equipment | |
MIL-STD-1189 | Standard Department of Defense Bar Code Symbology | |
ARP 1231 | O-ring gland design considerations. | |
ARP 1232 | O-ring gland design for static, radial squeeze. | |
ARP 1233 | O-ring gland design for dynamic, radial squeeze. | |
ARP 1234 | O-ring gland design for static and dynamic axial squeeze. | |
NAS 1515 | Washers - Plastic and Synthetic Rubber. | |
SMS 1586 | Swedish Military Standard Dimensions for (metric) O-Rings | |
SMS 1587 | Sealing elements - O-rings - Material | |
SMS 1588 | Sealing elements - O-rings - Housings | |
NAS 1593 | Two hundred and forty-nine standard O-ring sizes. Dash numbers correspond with AS-9746-568. Material is a high-temperature, fluid-resistant, fluorocarbon rubber per MIL-R-83248 Type 1, Class 1 (70-80 durometer). | |
NAS 1594 | Two hundred and forty-nine standard O-ring sizes. Dash numbers correspond with AS 568. Material is a high-temperature, fluid-resistant, fluorocarbon rubber per MIL-R-83248 Type 1, Class 2 (85-95 durometer). | |
NAS 1595 | Twenty standard O-ring sizes. Dash numbers correspond with AS 568 straight thread tube fitting boss gaskets (900 series). Material is a high-temperature, fluid-resistant, fluorocarbon rubber per MIL-R-83248 Type 1, Class 1 (70-80 durometer). | |
NAS 1596 | Twenty standard O-ring sizes. Dash numbers correspond with AS 568 straight thread tube fitting gasket (900 series). Material is a high-temperature, fluid-resistant, fluorocarbon rubber per MIL-R-83248 Type 1, Class 2 (85-95 durometer). | |
NAS 1598 | Sealing washer Metal washer with synthetic rubber O-ring bonded to inside diameter. | |
SAE J 1601 | Rubber Cups for Hydraulic Actuating Cylinders. | |
SAE J 1603 | Rubber Seals for Hydraulic Disc Brake Cylinders | |
SAE J 1604 | Rubber Boots for Drum Type Hydraulic Brake Wheel Cylinders | |
SAE J 1605 | Brake Master Cylinder Reservoir Diaphragm Gasket | |
NAS 1611 (T) | Two hundred and forty-nine standard O-ring sizes. Dash numbers correspond with AS 568. Material is ethylene propylene per NAS 1613. | |
NAS 1612 (T) | Twenty standard O-ring sizes. Dash numbers correspond with AS 568 straight thread tube fitting boss (900 series). Material is ethylene propylene per NAS 1613. | |
NAS 1613 (T) | Phosphate Ester Resistant O-ring Packing Qualification testing procedures and material specifications. | |
BIS BS 1806 | Specification for dimensions of toroidal sealing rings (O-Rings) and their housings (inch series) | |
ZZ-R-768 | Rubber for Mountings (Unbounded Spool and Compression Types) Used for shock protection. | |
AIR 786 | Rubber-fluid compatibility information. | |
ZZ-C-796 | Inflatable Ring Cushion | |
MIL-STD-810 | Environmental Test Methods for accelerated aging tests. | |
MIL-STD-831 | Preparation of Test Reports | |
ISO 2230 | Rubber products – Guidelines for storage | |
MIL-R-2765 | Synthetic rubber material for use as gaskets where resistance to oil and serviceability to temperatures above -20°F are required. | |
AMS 2817 Type 1 envelope | Packaging and Identification of Preformed Packings Individual packaging and marking of O-ring. in heat-sealed envelopes - Polyethylene-lines natural kraft paper of 30lb. min. wt. per ream (opaque both sides). | |
AMS 2817 Type 2 envelope | Packaging and Identification of Preformed Packings Individual packaging and marking of O-ring. in heat-sealed envelopes -One side as Type I, one side 300 gage cellophane coated with polyethylene. | |
MIL-P-2911 (Q) Type I | Hydraulic Conical and V Types Packing Assembly Fiber reinforced at least 40% by weight - Hydraulic Conical | |
MIL-P-2911 (Q)Type II | Hydraulic Conical and V Types Packing Assembly Fiber reinforced at least 40% by weight - Hydraulic V | |
MIL-G-3036 | Hot-Oil and Coolant Resistant Rubber Grommet | |
AN 3067 | 3/8 Inch Conduit Boss Seal Assembly | |
AS 3084 | Twenty Standard O-ring sizes. Dash numbers correspond to AS 568 straight fluorocarbon rubber per AMS 7280. | |
AS 3085 | Preformed Packing Three hundred and forty-nine standard size O-rings. Dash numbers correspond with AS 568. Material is a 70-80 durometer fluorocarbon per AMS 7280. | |
MIL-T-3100 (Q) | Solid Rubber Tires | |
MIL-S-3136 | Hydrocarbon Standard Test Fluids Supplanted by TT-S-735. | |
MIL-D-3377 Type I | Synthetic Rubber Diaphragms - Synthetic rubber composition without reinforcement | |
MIL-D-3377 Type II | Synthetic Rubber Diaphragms - Synthetic rubber reinforced with fabric | |
MS 3420 | Adapter, Clamp to Cable, Bushing, Telescoping | |
MIL-R-3533 Type I & II | Sheet, Strip and Molded Synthetic Rubber Oil and salt water resistant - Grade A, 75-85 durometer | |
MIL-R-3533 Type I & II | Sheet, Strip and Molded Synthetic Rubber Oil and salt water resistant - Grade B, 65-75 durometer | |
MIL-G-3545 | High Temperature Aircraft Grease | |
AS 3570 | Packing, Preformed - O-Ring Seal Material per AMS 7274 | |
ISO 3601/1 | Fluid Power Systems - O-Rings Inside diameters, cross sections, tolerances and size identification code. | |
ISO 3601/2 | Fluid Power Systems - O-Rings Housing dimensions for general applications. | |
ISO 3601/3 | Fluid Power Systems - O-Rings Quality acceptance criteria. | |
ISO 3601/4 | Fluid Power Systems - O-Rings Anti-extrusion rings (back-up rings). | |
ISO 3601/5 | Fluid Power Systems - O-Rings Suitability of elastomeric materials for industrial applications. | |
AMS 3651 | Polytetrafluoroethylene | |
DIN 3771 | O-Rings for use in fluid power systems. | |
MIL-P-3803 | Plastic, Polyethylene, Molded and Extruded Shapes, Sheets and Tubing | |
ASTM D 3951 Level A | Standard Practice for Commercial Packaging - Individual packaging in opaque bags, in accordance with MIL-P-116 | |
ASTM D 3951 Level C | Standard Practice for Commercial Packaging - Good commercial practice, 1, 5, 50, or 100 per bag | |
BIS BS 4518 | Specification for Metric dimensions of toroidal sealing rings (O-Rings) and their housings | |
MIL-P-4861 | Packaging of Preformed Rubber Packing | |
MIL-S-5049 (Q) Type M | Piston Rod Scrapers Performance requirements and qualification tests - all metal | |
MIL-S-5049 (Q) Type R | Piston Rod Scrapers Performance requirements and qualification tests - containing rubber | |
MIL-S-5049 (Q) Type R Class 2 | Piston Rod Scrapers Performance requirements and qualification tests - containing rubber, usable temperature range -65° to 275°F | |
MIL-P-5315 (Q) | Hydrocarbon Fuel Resistant Preformed Packaging Material is 60-70 durometer nitrile. | |
ARP 5316 | Storage of Elastomer Seals and Seal Assemblies Which Include an Elastomer Element Prior to Hardware Assembly. | |
MIL-B-5423 | General Specifications for Boots, Dust and Water Seal (for Toggle and Push Button Switches, Circuit Breaker and Rotary Actuated Parts) | |
MIL-G-5510 (Q)MIL-G-5514 | Straight Thread Tube Fitting Boss Preformed Packings Material is 88 durometer nitrile.Gland design recommendations for standard size O-rings. Complete engineering design consideration for O-ring installation. | |
AMS-P-5516 (Q) Class A | Specifies two classes of preformed packings for use where resistance to hydraulic fluid is required at temperatures from -65° to 160°F - Low Flexibility 83-93 durometer nitrile | |
AMS-P-5516 (Q) Class B | Specifies two classes of preformed packings for use where resistance to hydraulic fluid is required at temperatures from -65° to 160°F. - High Flexibility 63-72 durometer nitrile | |
MIL-W-5521 (Q) | Aircraft Hydraulic Packing Backup Washer Leather. | |
MIL-F-5566 | Anti-Icing Fluid (isopropyl alcohol) | |
MIL-G-5572 | Aviation Gasoline Grades 80/87, 100/130, 115/145 | |
MIL-H-5606 | Petroleum Base Hydraulic Fluid | |
MIL-T-5624 | Aviation Turbine Fuel Grades JP-4 and JP-5 | |
MIL-R-5847 | Silicone Rubber Low-and High-Temperature and Tear Resistant Supplanted by ZZ-R-765. All Classes, grades and requirements remain the same. See ZZ-R-765 for compounds that qualify. | |
MIL-L-6081 | Jet Engine Lubricating Oil | |
MIL-L-6082 | Aircraft Reciprocating Engine (Piston) Lubricating Oil | |
MIL-H-6083 | Petroleum Base Hydraulic Fluid for Preservation and Testing | |
MIL-L-6085 | Low Volatility Aircraft Instrument Lubricating Oil | |
MIL-A-6091 | Specially Denatured Ethyl Alcohol | |
MIL-R-6130 | Chemically Blown Cellular Rubber | |
ISO 6149 | Connections for hydraulic fluid power and general use -- Ports and stud ends with ISO 261 metric threads and O-ring sealing. | |
MIL-C-6183 | Cork and Synthetic Rubber Composition Sheets for Aromatic Fuel and Oil Resistant Gaskets | |
AN 6225 | V-Ring Dimensions. Most of the 80 sizes shown are manufactured. Material specified is a 70 durometer nitrile per MIL-P-5516. However, V-Rings are available in other 90 durometer nitrile and Fluoroelastomer compounds. | |
AN 6226 | U-Cup Dimensions. All 53 sizes shown manufactured plus over 170 other U-Cup sizes. Material specified is a 70 durometer nitrile per MIL-P-5516 Class B. However, U-Cups are available in a wide range of compounds to meet your specific needs. | |
AN 6227 | Eighty-eight O-ring sizes corresponding with AS 568 but dash numbers are different. Material specified is a 70 durometer nitrile per MIL-P-5516. | |
AN 6228 | V-Ring, Female Adapters Sizes correspond to AN 6225. Material specified is aluminum alloy. | |
AN 6229 | V-Ring, Male Adapters Sizes correspond to AN 6225. Material specified is aluminum alloy. | |
AN 6230 | Fifty-two O-ring sizes corresponding with AS 568 but dash numbers are different. Material specified is a 70 durometer nitrile per MIL-P-5516. Entire size group has cross section 1/8 nominal, .139” actual. | |
AN 6231 | Hydraulic Piston Rod Scraper Superseded by MS28776. | |
AN 6238 | Hydraulic Replacement Reservoir Type Filler Element Gasket Material per MIL-P-5516 Class B. Flat Gaskets - 1 5.25” OD x 3.50” ID x 0.063” thick. | |
AN 6290 (Q)MIL-L-6387 | Box Gaskets, for use with MIL-H-5606 Hydraulic Fluid Material is an 88+ durometer nitrile per MIL-P-5510. “Synthetic Base Lubricant Oil | |
A-A-52047 | PURE GUM TUBING | |
AMS3212 | DISCONTINUED RUBBER SPEC | |
AMS7278 | REPLACED BY AMS7276 | |
AN6225 | V RINGS | |
AN6244 | LEATHER BACK-UPS | |
AN6246 | LEATHER BACK-UPS | |
AN931-X-X | GROMMETS | |
AS3551 | AMS7272 | |
HH-P-151E CL 2 | 4oz COTTON INSERT | |
HH-P-151F CL 2 | 12oz COTTON INSERT | |
M19622 | STUFFING BOX | |
M24211 | WAVE GUIDE SEALS | |
M24231 | CONNECTOR | |
M83527 | ELECTRICAL PLUG | |
MIL-B-121 | PACKAGING SPEC REPLACED BY MIL-PRF-121G | |
MIL-F-81334B | POLYESTER OPEN CELL FOAM | |
MIL-G-21610B | OBSOLETE GASKET | |
MIL-G-22529 | NYLON GROMMETS SUPERSEDED BY MS21266 | |
MIL-R-15624 | MOLDED, EXTRUDED SHAPES GASKET MATERIAL ONLY (NOT MOLDED O-RINGS) | |
MIL-R-2765D | MOLDED, EXTRUDED SHAPES GASKET MATERIAL ONLY (NOT MOLDED O-RINGS) | |
MIL-STD-2073 | PACKAGING SPEC | |
MS18211 | MACHINE SCREW | |
MS22529 | GROMMETS OBSOLETE | |
MS24211 | GASK-O-SEAL | |
MS27194 | GASK-O-SEAL | |
MS27195 | GASK-O-SEAL | |
MS27196 | GASK-O-SEAL | |
MS27197 | GASK-O-SEAL | |
MS27198 | GASK-O-SEAL | |
MS28772 | D RING | |
MS28776 | METAL CLAD WIPERS | |
MS28777 | LEATHER BACK-UPS | |
MS28932 | FELT STRIP | |
MS29561 | OBSOLETE | |
MS3393 | MIL-P-81716 | |
MS35336 | COUNTERSUNK TOOTH METAL WASHER | |
MS35338 | FASTENER | |
MS35769 | METAL COPPER GASKETS | |
MS35803 | LEATHER BACK-UPS MONARCH | |
MS51007 | OBSOLETE CONNECTOR GASKET | |
MS52000 | OBSOLETE CONNECTOR GASKET | |
MS90064 | CANCELLED AND REPLACED BY A-A-55549 | |
MS9015 | METAL PLUG | |
MS9024 | CLAMP | |
MS90484 | CONNECTOR GASKET | |
MS9058 | TEFLON | |
MS9134 | ASBESTOS GASKETS | |
MS9135 | ASBESTOS GASKETS | |
MS9136 | ASBESTOS GASKETS | |
MS9141 | METAL GASKET | |
MS9142 | METAL GASKETS | |
MS9202 | METAL GASKETS | |
MS9203 | METAL GASKET | |
MS9241 | CANCELLED O-RING SPEC | |
MS9355 | CANCELLED O-RING SPEC | |
MS9371 | METAL SEALS | |
MS9372 | METAL SEALS | |
MS9373 | METAL SEALS | |
MS9374 | METAL SEALS | |
MS9375 | METAL SEALS | |
MS9376 | METAL SEALS | |
MS9966 | FLUOROSILICONE O-RING | |
MS9967 | FLUOROSILICONE O-RING | |
NAS1368 | PLASTIC GROMMETS | |
ASTM D2000 AA | Standard Classification System for Rubber Products in Automotive Applications. Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric. materials - Natural Rubber, Polyisoprene | |
ASTM D2000 AA | Standard Classification System for Rubber Products in Automotive Applications. Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials- SBR | |
ASTM D2000 AA | Standard Classification System for Rubber Products in Automotive Applications. Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - Butyl | |
ASTM D2000 AK | Standard Classification System for Rubber Products in Automotive Applications. Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - Polysulfide (Thiokolâ) | |
ASTM D2000 BA | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - Ethylene Propylene | |
ASTM D2000 BA | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - High Temperature SBR | |
ASTM D2000 BA | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - Butyl | |
ASTM D2000 BC | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - Chloroprene (Neopreneâ) | |
ASTM D2000 BE | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - Chloroprene (Neopreneâ) | |
ASTM D2000 BF | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - Nitrile (Buna N) | |
ASTM D2000 BG | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - Nitrile | |
ASTM D2000 BG | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - Urethane, Millable gum | |
ASTM D2000 BK | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - Polysulfide (Thiokolâ) | |
ASTM D2000 CA | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - Ethylene Propylene (EPDM) | |
ASTM D2000 CE | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - Chlorosulfonated Polyethylene (Hypalonâ) | |
ASTM D2000 CH | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - Nitrile | |
ASTM D2000 DA | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - Ethylene Propylene (EPDM) | |
ASTM D2000 DE | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - Chloroprene (Neopreneâ) | |
ASTM D2000 DE | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - CSM (Hypalonâ) | |
ASTM D2000 DF | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - Polyacrylic (butyl-actylate type) | |
ASTM D2000DH | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - Polyacrylic | |
ASTM D2000 EE | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - AEM (Vamacâ) | |
ASTM D2000 EH | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - ACM (Polyacrylic) | |
ASTM D2000 FC | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - Silicones (high strength) | |
ASTM D2000 FE | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - Silicones | |
ASTM D2000 FK | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - Fluorinated silicones (Fluorosilicone) | |
ASTM D2000 GE | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - Silicones | |
ASTM D2000 HK | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - Fluorinated elastomers (Vitonâ, Fluorelâ) | |
ASTM D2000 KK | Standard Classification System for Rubber Products in Automotive Applications Establishes a nomenclature system for ‘line call-outs’ for commercially available elastomeric materials - Perfluorinated elastomers (P-REX™) | |
M83528/001A- (001 thru013) | EMI Shielding | |
M83528/001B- (001 thru013) | EMI Shielding | |
M83528/001D- (001 thru 013) | EMI Shielding | |
M83528/001K- (001 thru013) | EMI Shielding | |
M83528/001M- (001 thru 013) | EMI Shielding | |
M83528/001C- (001 thru 013) | EMI Shielding | |
M83528/001E- (001 thru013) | EMI Shielding | |
M83528/001F- (001 thru 013) | EMI Shielding | |
M83528/001H- (001 thru 013) | EMI Shielding | |
M83528/001L- (001 thru013) | EMI Shielding | |
M83528/001G-(001 thru 013) | EMI Shielding | |
M83528/001J- (001 thru 013) | EMI Shielding | |
M83528/002A- (007 thru155) | EMI Shielding | |
M83528/002B- (007 thru155) | EMI Shielding | |
M83528/002D- (007 thru 155) | EMI Shielding | |
M83528/002K- (007 thru155) | EMI Shielding | |
M83528/002M- (007 thru 155) | EMI Shielding | |
M83528/002C- (007 thru 155) | EMI Shielding | |
M83528/002E- (007 thru155) | EMI Shielding | |
M83528/002F- (007 thru 155) | EMI Shielding | |
M83528/002H- (007 thru 155) | EMI Shielding | |
M83528/002L- (007 thru155) | EMI Shielding | |
M83528/002G-(007 thru 155) | EMI Shielding | |
M83528/002J- (007 thru 155) | EMI Shielding | |
M83528/003A- (001 thru012) | EMI Shielding | |
M83528/003B- (001 thru012) | EMI Shielding | |
M83528/003D- (001 thru 012) | EMI Shielding | |
M83528/003K- (001 thru012) | EMI Shielding | |
M83528/003M- (001 thru 012) | EMI Shielding | |
M83528/003C- (001 thru 012) | EMI Shielding | |
M83528/003E- (001 thru012) | EMI Shielding | |
M83528/003F- (001 thru 012) | EMI Shielding | |
M83528/003H- (001 thru 012) | EMI Shielding | |
M83528/003L- (001 thru012) | EMI Shielding | |
M83528/003G-(001 thru 012) | EMI Shielding | |
M83528/003J- (001 thru 012) | EMI Shielding | |
M83528/003A- (001 thru013) | EMI Shielding | |
M83528/003B- (001 thru013) | EMI Shielding | |
M83528/003C- (001 thru 013) | EMI Shielding | |
M83528/003D- (001 thru 013) | EMI Shielding | |
M83528/003E- (001 thru013) | EMI Shielding | |
M83528/003F- (001 thru 013) | EMI Shielding | |
M83528/003G-(001 thru 013) | EMI Shielding | |
M83528/003K- (001 thru013) | EMI Shielding | |
M83528/003L- (001 thru013) | EMI Shielding | |
M83528/003M- (001 thru 013) | EMI Shielding | |
M83528/004A- (001 thru036) | EMI Shielding | |
M83528/004B- (001 thru036) | EMI Shielding | |
M83528/004D- (001 thru 036) | EMI Shielding | |
M83528/004K- (001 thru036) | EMI Shielding | |
M83528/004M- (001 thru 036) | EMI Shielding | |
M83528/004C- (001 thru 036) | EMI Shielding | |
M83528/004E- (001 thru036) | EMI Shielding | |
M83528/004F- (001 thru 036) | EMI Shielding | |
M83528/004H- (001 thru 036) | EMI Shielding | |
M83528/004L- (001 thru036) | EMI Shielding | |
M83528/004G-(001 thru 036) | EMI Shielding | |
M83528/004J- (001 thru 036) | EMI Shielding | |
M83528/004- (001thru 036) | EMI Shielding | |
M83528/005A- (001 thru023) | EMI Shielding | |
M83528/005B- (001 thru023) | EMI Shielding | |
M83528/005D- (001 thru 023) | EMI Shielding | |
M83528/005K- (001 thru023) | EMI Shielding | |
M83528/005M- (001 thru 023) | EMI Shielding | |
M83528/005C- (001 thru 023) | EMI Shielding | |
M83528/005E- (001 thru023) | EMI Shielding | |
M83528/005F- (001 thru 023) | EMI Shielding | |
M83528/005H- (001 thru 023) | EMI Shielding | |
M83528/005L- (001 thru023) | EMI Shielding | |
M83528/005G-(001 thru 023) | EMI Shielding | |
M83528/005J- (001 thru 023) | EMI Shielding | |
M83528/006A- (001 thru 005) | EMI Shielding | |
M83528/006B- (001 thru 005) | EMI Shielding | |
M83528/006D- (001 thru 005) | EMI Shielding | |
M83528/006K- (001 thru 005) | EMI Shielding | |
M83528/006M- (001 thru 005) | EMI Shielding | |
M83528/006C- (001 thru 005) | EMI Shielding | |
M83528/006E- (001 thru 005) | EMI Shielding | |
M83528/006F- (001 thru 005) | EMI Shielding | |
M83528/006H- (001 thru 005) | EMI Shielding | |
M83528/006L- (001 thru 005) | EMI Shielding | |
M83528/006G-(001 thru 005) | EMI Shielding | |
M83528/006J- (001 thru 005) | EMI Shielding | |
M83528/007A- (001 thru 007) | EMI Shielding | |
M83528/007B- (001 thru 007) | EMI Shielding | |
M83528/007D- (001 thru 007) | EMI Shielding | |
M83528/007K- (001 thru 007) | EMI Shielding | |
M83528/007M- (001 thru 007) | EMI Shielding | |
M83528/007C- (001 thru 007) | EMI Shielding | |
M83528/007E- (001 thru 007) | EMI Shielding | |
M83528/007F- (001 thru 007) | EMI Shielding | |
M83528/007H- (001 thru 007) | EMI Shielding | |
M83528/007L- (001 thru 007) | EMI Shielding |